GI7B Six Meter Amplifier Project - Update 3

In the past couple of day, the six meter amplifier project moving very slow.

1) I have made the PCB Board Fabrication for High Voltage and Soft Start. This weekend, will go for the Software Key and Bias PCB.
2) I also drill two big holes for the front panel meter High Voltage and Plate Current meter. Although it is a tough work, which took me an hour to complete, it looks very nice.
3) I cut 80mm Telfon Rod of 20mm Diameter for the plate choke. SWG 22 wire expect arrive from UK within this week.
4) I bought one 12V 10A contact rating Omron relay from Apliu Street, which is for the T/R switching.

From the photo, you can see the soft start PCB mounted on the bottom of the chassis.

GI7B Six Meter Amplifier Project - Update 2

If is quite difficult to get small diameter of copper tubing. It needs to buy at least a roll of several meter of quantity. So I give up this kind of material. Looking around and thinking of using surplus short length of hard line cable, center conductor is 5mm diameter. Wound 4 turn, inner diameter 40mm.
Doorknob capacitor is 1000pf 15KV purchased from Mainland China.

GI7B Six Meter Amplifier Project - Update 1

Yesterday went to Canton road to cut the aluminum sheets for the front panel and partition for the chassis. Six pieces cost of $215. I also locate one winding transformer company and ask for the quote for a 1000VA transformer at a reasonable cost. Size is approx. 6”x6”x6” and delivery time is one week. I told the shop will prepare the specification and order next week. What a surprise that they have transformer oil (for my HN-31 Heathkit dummy load) in stock, which is very rare and difficult to find here.

The major component is ready and has tried to place them on the chassis and it looks fine.

Amplifier Chassis

Yesterday purchased 20 ft - 1 inch aluminum angle, which cut into small section for building the chassis of the GI7B amplifier. It cost $95 dollars including the entire cutting fee. The chassis’s dimension will be at (360mm D x 350mm W x 200mm H). When have time this weekend, I will go to Canton Road to source aluminum plate for internal partition, front and rear panel.

GI7B Socket Arrived

The beautiful pair of GI7B socket arrived.

Dinner gathering on 1 Dec

Wyn, VR2AX offer me a pair of old GE 3-500z tubes. By this occasion, I arranged a dinner gathering together with Steve, VR2XMQ and Martin, VR2/AA1ON. My XYL and Queanne (Martin’s colleague) also with us. We all have a very enjoyable time.

On Sunday afternoon, I tested the tubes with the following result:

1) Standby current (60mA for two) 25mA + 35mA. My old pair of Eimac took 110mA on both

2) Output power

80M = 850W
40M = 850W
20M = close to 900W
15M = 850W
10M = 650W

One is growing red.

Thank you Wyn for this nice gift to me.

ZL7/SP5EAQ - 40M QSO confirmed

I am very happy to confirm the QSO with ZL7/SP5EAQ on 40M. My antenna is a trap shorten dipole ( GM4JMU design ) with 100W from FT-2000.

GI7B Six Meter Amplifier Project

In year 2000, three of us ( VR2XMQ, VR2IL and me ) purchase a very nice Russian Tube (GI7B) from Dr. Alex UR4LL for the intention of building amplifier for six meters. We never start the project ...
Until early this year, VR2IL sold his tube to me. With the pair of tube, I start to plan the project, including:

1) collect of parts

• For the reason that commercial tube socket is not available and searching around the net and find it is available from W4ZT
• Power transformer, still searching around if it is available to wind in local market. Otherwise, may need to find in Mainland.

2) Circuit - I refer to use YU1Aw design.

I will update any more status of this project in future.

QSL Card Printing

In the past two years, my entire QSL card was printed by QSL Printer in China. The printing quality was good in the very first beginning, however, those current batch of VR10 cards were really disappointed.
1) The cards are curled, probably due to overheat during the laminated process
2) The color not exactly the same, very dark and contrast no good

Last month, UX5UO , a QSL card printer from Ukraine sent me a promotion e-mail about his service. They offer me a sample of 1000 cards for US$22 (shipping cost only)

Without hesitation, I accepted their offer and sending them my shack photo as the QSL card front and simple text design for the back side. After three weeks, the cards arrived and I am very happy with the printing quality. They well care of my image file and edit with their professional skill.
No doubt, my next batch of card printing will go to them for sure.

9U0A & 5U5U QSL Cards

Received very nice QSL card from 9U0A and 5U5U.

SB-200 Power Supply Board

No DX on the band, so spent sometime to upgrade some of the ham equipment. The SB-200 HV have a certain drop when load. So I decided to upgrade the board:
1) replace all capacitors to 270 uF 450V 105 degree c
2) replace all rectifier diodes to IN5408
3) all bleeding resistors from 30K to 100K ohms

It was completed and the high voltage much more stable now.

SB-220 with vacuum variable

I have problem with the tune cap arcing in the SB-220 and caused some damage to the components.

Recently I purchased one 5-250 pF vacuum variable from ebay and installed it for a trial. It works very good from 15M to 80M, but look like it is not working well on 10M. This problem need to be sort out when have free time.

PVRM

On 27 Oct, my birthday, gave me a good memory.

I ran through an auction via the Transport Dept Private Vechicle Rigistration Mark Scheme that have my radio amateur radio callsign as the mark.

It is on my car now.

Shack photo

A new photo was taken on 10 Oct at my radio shack. you can see the new radio FT-2000 sitting in the middle.... cool !!

Six meter QSL card

Today I completed the design of my six meter QSL card.

It use the 3-500z as background.